Paying a plumber to fit a new kitchen or bathroom faucet is a small job, and what you pay depends mostly on what is under the sink. The best published figures we could read cover garbage disposals: This Old House gives $150 to $950 for the unit plus installation, and $410 to $1,300 when a faucet and a disposal are done together. It belongs with faucets, sinks, showers and disposals, and below those numbers are split into parts.
What is the labor cost for a faucet swap?
None of the sources we read gave a clean faucet-only labor figure, and we will not invent one. They do show hourly labor: handypersons at $50 to $75, plumbers up to $150. A swap with working shutoffs goes fast; seized fittings or missing shutoffs add time. Treat all of this as a guide, since the real number is whatever the plumber writes on the quote after seeing your sink.
The quote should say whether the faucet comes from you or from the plumber. Faucets vary hugely, and a pull-down or touchless model takes longer to set up and to link to a sprayer, filter or soap line. Bought one online? Have the plumber check the fit before the box is opened.
What should a garbage disposal installation run?
This Old House puts the combined cost of the unit and installation at $150 to $950, with typical averages of $400 to $500. Most homes need a unit that costs $150 to $250; prices run from $75 for the smallest model to up to $1,000 for a 2 horsepower unit. Professional installation takes about one to four hours. Prices on your quote will differ from these averages, and the quote is what counts.
Breaking it down further, the same source lists continuous-feed units at $75 to $500 and batch-feed at $200 to $650, and by motor size from $75 to $200 for a one-third horsepower unit up to $300 to $1,000 for 2 horsepower. Brand matters too: Waste King runs $74 to $180 and KitchenAid $249 to $649. Repairing a disposal whose motor still works costs $50 to $400, but replacement is usually cheaper than repair, and units last about 10 years. The work itself is described in garbage disposal installation service.
What makes one quote higher than another?
Four factors dominate: whether a disposal was there before, the electrical side, the unit you pick, and what is under the sink. A straight swap where wiring and drain already exist sits at the cheap end. A first-time disposal needs a new outlet or switch, a drain change and often a new dishwasher connection, which is the expensive end.
On electrical work, This Old House says the biggest part of a first-time install is often the electrical, and continuous-feed models need an electrician, who typically charges $50 to $120 an hour. Add $400 or so if the sink itself has to be replaced, plus the sink. Local water adds a wrinkle. Ontario's 2025 water report lists hardness averaging 91 to 177 ppm depending on the source, and mineral scale can seize old shutoffs and aerators, stretching a quick swap. Ask about shutoffs before the visit. Work needing a permit, or reaching $1,000 for labor and materials together, has to go to a contractor with a California license.
How do hardwired, button and plug-in disposals compare?
A plug-in disposal takes power through a cord from an outlet beneath the sink, the simplest swap. A hardwired one is connected directly to the circuit and may need an electrician. A button or air-switch model adds a small button on the counter, so there is an extra hole and a tube. A batch-feed disposal runs only when the stopper is turned.
Pick for the room you have and the habits in the house. Brands such as Moen and GE use different mounting rings and gasket styles, and every maker publishes its own instructions, which an installer should follow. A worn flange gasket is a common leak point and is a small part. When comparing quotes, check for the cord or wiring kit, the drain hookup and removal of the old unit.
Can I install a faucet or disposal myself?
A faucet, yes, if a wrench does not scare you and the shutoffs close. Plenty of owners follow a video and finish in an afternoon. A disposal is tougher: heavy parts overhead in a cabinet, a drain to line up and often wiring. Hand the wiring to an electrician or plumber.
A video shows steps but not the state of your own plumbing. Shutoffs that will not close fully, or old galvanized drain, mean stop and call someone. Errors under a sink show up later as slow leaks. If the old fixture only needs a repair, fixing a leaky faucet may save the swap.
What about shower repairs?
Showers are another animal. A cartridge, trim or showerhead is often quick, but a valve behind tile means opening the wall. Plumbers price by access and by what failed. We have no dependable shower figure from the sources we read, so a written quote after a look is the only real price.
For a drip at the head or a handle that will not stop the flow, begin with fixing a leaky shower faucet. Water showing in a wall or ceiling calls for a quick look at a shower leak.
How should two quotes for fixture work be compared?
Lay them side by side on the same scope: who supplies the faucet or disposal, new shutoffs and supply lines, wiring, drain connection, old-unit removal, any permit, and the time estimate. A bid that omits shutoffs or wiring is not really lower. Get the license number and verify it with the state.
Get the price in writing ahead of the visit, and ask what happens if something turns up mid-job, such as a corroded drain or a missing shutoff. California requires a written contract once a home improvement job reaches $500, and it limits home improvement deposits. A fair quote lists parts and labor separately.
Common questions
How many hours does the job take?
This Old House says professional disposal installation takes about one to four hours. A faucet swap tends to be shorter when shutoffs work and longer if fittings are stuck. Get an estimate and find out if it includes cleanup. Wiring or a changed drain is what usually stretches the visit.
Which questions come before the booking?
Ask for the license number, a quote splitting parts from labor, who buys the faucet or disposal, whether shutoffs are included, and the plan if wiring or drain changes appear. Raise the permit question when electrical work is involved. Request every answer in writing.
Does someone need to be in the house?
Ideally yes: at the beginning to show the work area and shutoff, and at the end to inspect. Empty the under-sink cabinet beforehand. After a disposal goes in, run it with water flowing before the plumber leaves and look underneath for drips.
Is a disposal worth installing in an Ontario kitchen?
It is a convenience, not a necessity, and it adds a part that can jam or leak. If you cook a lot and use the drain heavily, it helps, but it does not replace scraping plates. Check the sink and drain first, because a disposal only adds load to a drain that is already slow. A clogged disposal is a frequent reason people ring a plumber.
Will a new faucet cure weak flow at the sink?
Sometimes, when the old one has a clogged aerator or a worn cartridge, but a new faucet cannot fix a weak supply. If every tap runs weak, look elsewhere; kitchen faucet low water pressure comes first. The home page lists the rest of our services.