Hissing at 2 a.m., a puddle at the base, a handle that needs three tries: these are the three calls that reach us most for toilets in Ontario. Tell us which one you have, and we'll book a local plumber who turns up with the likely parts on board. Below you'll find the faults behind each symptom, rough dollar figures, and where a handyman runs out of road. Ready now? Request a quote or go back to the Chaffey Pipe and Drain home page.
What actually breaks inside a toilet tank, and how do you spot it?
Three parts fail again and again: the flapper (rubber seal), the fill assembly (the tall float-operated unit that refills the tank), and the flush seat the flapper rests on. Lift the lid, flush once, and follow the flow with your eyes. That single test usually points at the culprit within a minute.
A slow trickle past the seal while the tank level drops means the seal has gone soft or the seat is pitted. Water climbing all the way to the overflow tube, then spilling down it, means the refill unit never shuts itself off. A tank that refills with a long hiss and no obvious loss hints at an over-raised float or a worn washer inside the valve.
Ontario water adds its own wear. The city's utility reports hardness averaging 91 to 177 ppm in 2025, depending on which source feeds your block. Minerals crust onto rubber and stiffen it, which is why flappers here often fail before the porcelain shows a mark.
Which toilet fix is the one plumbers do most?
Swapping the flapper wins easily. It costs a few dollars in parts, is done in well under thirty minutes, and silences the commonest complaint, the bowl that tops itself up with no one near it. When it doesn't cure the problem, the plumber moves to the refill unit, then to the seat underneath.
Our guides go further on each step: the page on toilets that keep running, the one on flapper replacement, the refill valve walk-through, and the notes on reaching a worn flush valve.
Chain length trips people up. Too much slack lets the flapper hang open; too little holds it off the seat. Fixing a chain costs nothing, so a good visit starts there.
Is a handyman enough for a leaking toilet?
Often yes. Swapping a flapper, a float assembly or a braided supply line needs no special trade skill, and most such jobs stay under California's $1,000 threshold for contractor licensing (the same board requires one wherever a permit applies). Water at the floor is another story: think failed wax seal, cracked flange or spongy subfloor.
Match the person to where the water shows. Tank only: parts. Around the base: the bowl must be lifted. Staining on a ceiling below: stop flushing and call quickly, because the floor may have been damp for a while.
Try the dye test before booking anything. Drop in two squirts of food coloring, walk away for ten minutes, and don't flush. EPA's WaterSense page says color in the bowl afterward proves a leak. The same page adds that an aging flapper can drain thousands of gallons yearly without a sound, and that homes lose more than 9,300 gallons a year to all leaks combined.
How much is a running toilet to repair?
One 2026 national price guide lists $50 to $120 for a flapper swap and $60 to $150 for a fill valve, with a combined visit landing near the top of those bands. Parts are cheap. You're mostly paying for the trip and the hands. California pricing may sit above that guide, so read it as a starting point.
The same guide breaks out other fixes. Treat them as orientation, not a quote.
| Problem | Guide range |
|---|---|
| Flapper | $50 to $120 |
| Fill valve | $60 to $150 |
| Flush valve | $100 to $250 |
| Handle or lever | $50 to $120 |
| Supply line leak | $50 to $130 |
| Shut-off valve leak | $100 to $225 |
| Base leak (wax ring) | $150 to $275 |
| Professional auger for a clog | $100 to $275 |
After-hours calls add 30 to 50 percent on that guide. If the whole fixture is tired, compare against the full replacement price page. Only an itemized written quote after someone sees your bathroom settles the real price. No table can see inside your tank.
Which other bathroom problems travel with a bad toilet?
Slow sink drains, dripping faucets, weak shower flow and sticky handles often show up together, because fixtures in one bathroom share supply and drain runs. When two things go wrong in the same week, suspect something upstream: a branch line starting to narrow, or pressure drifting at the house.
Several symptoms have their own write-ups. A handle that goes slack and won't flush is generally a snapped arm. A leaking toilet needs its source traced before parts get swapped. Water running over the overflow standpipe has its own overflow tube repair notes.
If the bowl is blocked, not broken, head to clogged toilet help. Drainage services for a backed-up main run are priced separately.
Heating gear is a different trade, so a toilet visit won't touch your water heater unless you say so. Mention a cold-water complaint on the request and we'll note both.
Common questions
Fair money for a blocked toilet?
Expect roughly $100 to $275 for professional auger work, going by a national guide. Budget higher if the bowl must be pulled off the flange, or the plug is far down the pipe. More detail is on the toilet unclogging costs. Get the final figure on paper before anyone starts.
Does a clogged bowl ever drain by itself?
A soft paper clog sometimes dissolves overnight, but it's a gamble. Resist flushing again, because a full bowl spills onto the floor. If the level is climbing, twist the little stop valve at the wall. Wipes, toys and mineral buildup never dissolve; those need a plunger or an auger.
Is there a standard rate for toilet unclogging?
No single rate applies. One national guide lists $100 to $275 for an auger visit, with camera work for repeat blockages billed separately and evening hours costing more. Get a full figure first, and find out how the figure shifts if the plug turns up in the main line.
What does swapping a whole toilet involve?
Close the stop valve, drain the tank, disconnect the supply hose, remove the base nuts, then lift the bowl off. New wax and a level set keep the next one sealed. Because the porcelain is heavy and a bent flange ruins the seal, plenty of homeowners hand this one over.
Can I buy only a new tank?
A cracked tank alone runs about $200 to $400 in a national guide, and only when a matching tank is still sold. Tanks and bowls are made as pairs, so many plumbers suggest a whole new toilet instead. Ask the quote to show both options side by side.